Just How to Replace a Bath Tub
Just How to Replace a Bath Tub
Blog Article
This great article down below on the subject of Tools You Need to Install a New Bathtub is especially compelling. Check it out for yourself and decide what you think about it.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the task can move speedily; if you need to open a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub and also embeded in the new one. See to it you have certified yourself for the job and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your restroom if you have currently purchased a brand-new tub as well as don't need to change the setup of your previous water pipes.
Your tools and also material list must comprise the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather problematic because of the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, place the tub in the called for placement. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The following objective is to make certain that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bath tub till the level reviews degree.
To set up faucets, fit the bottom of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Ultimately, fix the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the tub should wait until the bath tub has actually been used at least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Secure the faucet in position with the producer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can fracture fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very focused on Installing A Bathtub and I'm hoping you appreciated the blog entry. Those who liked our page if you please be sure to pass it around. We take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.
Prices & Booking Report this page